Reference
perlnumber  semantics of numbers and numeric operations in Perl
 $n = 1234; # decimal integer
 $n = 0b1110011; # binary integer
 $n = 01234; # octal integer
 $n = 0x1234; # hexadecimal integer
 $n = 12.34e56; # exponential notation
 $n = "12.34e56"; # number specified as a string
 $n = "1234"; # number specified as a string
This document describes how Perl internally handles numeric values.
Perl's operator overloading facility is completely ignored here. Operator overloading allows userdefined behaviors for numbers, such as operations over arbitrarily large integers, floating points numbers with arbitrary precision, operations over "exotic" numbers such as modular arithmetic or padic arithmetic, and so on. See overload for details.
Perl can internally represent numbers in 3 different ways: as native
integers, as native floating point numbers, and as decimal strings.
Decimal strings may have an exponential notation part, as in "12.34e56"
.
Native here means "a format supported by the C compiler which was used
to build perl".
The term "native" does not mean quite as much when we talk about native integers, as it does when native floating point numbers are involved. The only implication of the term "native" on integers is that the limits for the maximal and the minimal supported true integral quantities are close to powers of 2. However, "native" floats have a most fundamental restriction: they may represent only those numbers which have a relatively "short" representation when converted to a binary fraction. For example, 0.9 cannot be represented by a native float, since the binary fraction for 0.9 is infinite:
 binary0.1110011001100...
with the sequence 1100
repeating again and again. In addition to this
limitation, the exponent of the binary number is also restricted when it
is represented as a floating point number. On typical hardware, floating
point values can store numbers with up to 53 binary digits, and with binary
exponents between 1024 and 1024. In decimal representation this is close
to 16 decimal digits and decimal exponents in the range of 304..304.
The upshot of all this is that Perl cannot store a number like
12345678901234567 as a floating point number on such architectures without
loss of information.
Similarly, decimal strings can represent only those numbers which have a finite decimal expansion. Being strings, and thus of arbitrary length, there is no practical limit for the exponent or number of decimal digits for these numbers. (But realize that what we are discussing the rules for just the storage of these numbers. The fact that you can store such "large" numbers does not mean that the operations over these numbers will use all of the significant digits. See "Numeric operators and numeric conversions" for details.)
In fact numbers stored in the native integer format may be stored either in the signed native form, or in the unsigned native form. Thus the limits for Perl numbers stored as native integers would typically be 2**31..2**321, with appropriate modifications in the case of 64bit integers. Again, this does not mean that Perl can do operations only over integers in this range: it is possible to store many more integers in floating point format.
Summing up, Perl numeric values can store only those numbers which have a finite decimal expansion or a "short" binary expansion.
As mentioned earlier, Perl can store a number in any one of three formats, but most operators typically understand only one of those formats. When a numeric value is passed as an argument to such an operator, it will be converted to the format understood by the operator.
Six such conversions are possible:
 native integer > native floating point (*)
 native integer > decimal string
 native floating_point > native integer (*)
 native floating_point > decimal string (*)
 decimal string > native integer
 decimal string > native floating point (*)
These conversions are governed by the following general rules:
If the source number can be represented in the target form, that representation is used.
If the source number is outside of the limits representable in the target form, a representation of the closest limit is used. (Loss of information)
If the source number is between two numbers representable in the target form, a representation of one of these numbers is used. (Loss of information)
In native floating point > native integer
conversions the magnitude
of the result is less than or equal to the magnitude of the source.
("Rounding to zero".)
If the decimal string > native integer
conversion cannot be done
without loss of information, the result is compatible with the conversion
sequence decimal_string > native_floating_point > native_integer
.
In particular, rounding is strongly biased to 0, though a number like
"0.99999999999999999999"
has a chance of being rounded to 1.
RESTRICTION: The conversions marked with (*)
above involve steps
performed by the C compiler. In particular, bugs/features of the compiler
used may lead to breakage of some of the above rules.
Perl operations which take a numeric argument treat that argument in one of four different ways: they may force it to one of the integer/floating/ string formats, or they may behave differently depending on the format of the operand. Forcing a numeric value to a particular format does not change the number stored in the value.
All the operators which need an argument in the integer format treat the
argument as in modular arithmetic, e.g., mod 2**32
on a 32bit
architecture. sprintf "%u", 1
therefore provides the same result as
sprintf "%u", ~0
.
The binary operators +

*
/
%
==
!=
>
<
>=
<=
and the unary operators 
abs
and 
will
attempt to convert arguments to integers. If both conversions are possible
without loss of precision, and the operation can be performed without
loss of precision then the integer result is used. Otherwise arguments are
converted to floating point format and the floating point result is used.
The caching of conversions (as described above) means that the integer
conversion does not throw away fractional parts on floating point numbers.
++
behaves as the other operators above, except that if it is a string
matching the format /^[azAZ]*[09]*\z/
the string increment described
in perlop is used.
use integer
In scopes where use integer;
is in force, nearly all the operators listed
above will force their argument(s) into integer format, and return an integer
result. The exceptions, abs
, ++
and 
, do not change their
behavior with use integer;
Operators such as **
, sin
and exp
force arguments to floating point
format.
Arguments are forced into the integer format if not strings.
use integer
forces arguments to integer format. Also shift operations internally use signed integers rather than the default unsigned.
force the argument into the integer format. This is applicable
to the third and fourth arguments of sysread
, for example.
force the argument into the string format. For example, this is
applicable to printf "%s", $value
.
Though forcing an argument into a particular form does not change the stored number, Perl remembers the result of such conversions. In particular, though the first such conversion may be timeconsuming, repeated operations will not need to redo the conversion.
Ilya Zakharevich ilya@math.ohiostate.edu
Editorial adjustments by Gurusamy Sarathy <gsar@ActiveState.com>
Updates for 5.8.0 by Nicholas Clark <nick@ccl4.org>
Recently read
Tools